Spiritual

BREMSHEY ORBIT PLUS MANUAL PDF

February 15, 2019

You can find the manual for your Bremshey Cross Trainer below. Bremshey Orbit Ambition Cross Trainer · Bremshey Orbit Control Cross Trainer · Bremshey. Check the reed sensor also known as the speed sensor. It is located on the front roller pulley. It is mounted to the frame and looks like a small. 18TSFC_Star Fit C HR i-Plus Crosstrainer_OMpdf . _Bremshey Orbit Ambition C_User Manual. pdf. MB.

Author: Kanris Mausida
Country: Mayotte
Language: English (Spanish)
Genre: Music
Published (Last): 6 February 2016
Pages: 383
PDF File Size: 13.6 Mb
ePub File Size: 1.1 Mb
ISBN: 600-9-20572-900-8
Downloads: 1168
Price: Free* [*Free Regsitration Required]
Uploader: Yokus

Action to rectify 1. The primary intention of this Service Manual is to enhance the reader’s knowledge of the structures of the Tunturi bike ergometers E30, Orrbit, E45, E60, E80 and E85 and Tunturi fitness bike F30 autumn onwards.

The axle is secured by 2 nylok nuts and supporting washers See diagram.

Manual – Bremshey Orbit Fit (b) Cross Trainer

Set the rear drum so that the axle stub is in a vertical position. Un-plug main power supply.

Switch on power and plsu resistance to maximum from meter 4. When two materials with different electrical potentials are brought together, a static shock or electrostatic discharge ESD can occur. Check profiles on display increase.

Manual – Bremshey Orbit Control Cross Trainer

Loosen the two securing bolts for the rear roller by turning counter clockwise. Remove the circlip and washer located on the end of the axle projecting through the right side and then pull the left side unit away. Resistance is measured from black and white wires see picture in 3rd page. Tap the end of the drift with a hammer until the one bearing is removed. Check suitability of user. To unfold the treadmill, hold the handle bar firmly with the left hand, opposite if left-handed using bresmhey right hand, grasp the upper bar of the bed frame and push in towards the face of the console, step on the locking lever to lift it clear of the locking bar and then pull the bed forward toward you.

TOP Related Articles  DIGITAL MULTIMETER DT9205A MANUAL PDF

Static will only travel from a charged material to a neutral material.

Bremshey Orbit Fit (4182b) Cross Trainer

Otherwise, call the dealer for service. The spring can be discarded as it is not absolutely required. Remove wheel bracket from frame. Foot tube assembly Check correct power supply see list. If the machine was charged, there would be no discharge of orbut.

Search results

Calibration parameters of User Interface are not valid. Remove the power cord. The question will be displayed again after restart. Replacement of motor is completed and we can put shroud cover back. For identifying a specific problem see the Troubleshooting Guide and then refer to appropriate area if necessary.

Now lift the cable over the motor capstan e and then slide out the cable end from the capstan slot. Measure electromagnet coil total resistance, it should not be zero or infinite. The covers can now be removed.

Pluss an anti-static strap will eliminate static discharge, it can be annoying to the user. Speed sensor not properly assembled, the distance between the magnet and the speed sensor should be less than 3mm. Whilst rotating the rear drum, increase the resistance with the meter keys to maximum checking that the cable and flywheel slider is moving freely.

Unplug power supply wire to tension motor. Orbot more details about updating the user interface software in chapter 4 Set the meter’s audio signals on brmshey off Adjust display contrast The Service menu is for Tunturi service personnel only and can be accessed with following routine 1. Only needs to be done on one side. Screw the lower adjusting bolt until a satisfactory tension is achieved.

Move the plug, is power intermittent? Slacken off the vertical tensioning bar by loosening the upper and lower locking bolts f and then remove lower adjusting bolt g 2. Replacing the components does not require special tools, but assumes a certain level of technical competence and familiarity with basic hand tools.

TV and mobile phone, and electric network can generate interference. NA Height storage position It assumes a certain level of technical competence and familiarity with basic hand tools.

TOP Related Articles  INTELLIFILE PC INTERFACE PDF

This product therefore carries the CE label. If the unit cannot be pulled off, tap the end of the axle gently with a soft faced hammer until removed. If necessary rotate the drum until the tube eases off. Speed sensor cable disconnected Meter cable has a poor connection at some point Magnet missing from the front roller pulley Front roller not rotating at all due to loose drive belt Check the distance between the speed sensor and the flywheel and ensure that the speed sensor is properly attached to the motor frame.

Only user interface parameters are valid within the limits 4. Rotate drum in an anti – clockwise direction simulating forward motion in use. Replacing the servo-motor unit If it is established that the servo-motor will not respond as it is faulty it will be necessary to exchange it. The first one, Settings menu, is a public menu available also to the end user and accessed via normal menus under user settings. The circuit board can be replaced by removing 4 x screws fixing it to the frame l and unplugging the cables.

There are several screws located on the perimeter of the covers. The parameters will be used only until next start-up, unless separately saved in the memory with ‘Save’ function Please refer to chapter 3. E6 Instruction in the owner’s manual: Taking care to refit the cable around the motor capstan in the correct direction and avoiding strain on the cable which may damage the motor gearing mechanism.

If the readout from the potentiometer is 1 the software is not picking any signal from the potentiometer Possible reasons: Push the flywheel slider c down with a screwdriver and the release the outer cable sleeve d from the servo-motor securing point.

Section 4 Bearings and joints The linkages between the swing arm, foot-tube and rear brace involve 3 main joints and bearings.