FFT10 interface or RS interface. For. For. EKC EKC For. For .. Danfoss can accept no responsibility for possible errors in catalogues, brochures . Introduction. Features. EKC (for panel mounting) and EKC EKC and are used for. • temperature Danfoss Pt sensors are supplied with . Danfoss EKC – Download as PDF File .pdf), Text File .txt) or read online.
|Published (Last):||21 September 2008|
|PDF File Size:||8.40 Mb|
|ePub File Size:||19.73 Mb|
|Price:||Free* [*Free Regsitration Required]|
It’s a community-based project which helps to repair anything. If you want to change the periodical defrost, so that it can be performed at specific times of the day, a clock module may be fitted.
People who viewed this also viewed. Example on menu pictures Alarms If the controller is extended with data communication, it will be possible to define the kec of the transmitted alarms.
Controller for temperature control – EKC and EKC Manual |
All alarms are indicated by the three LEDs flashing at once. The time delay is set in minutes. Real time clock battery driven can be fitted. Here you simply set how often defrost is to be star ted. The controllers are subsequently connected with a two-core cable. Send This is not what you are looking for?
Danfoss Electronic Controller (EKC EKC ) –
The operation of the controller can now be ekd out via the data communication. Send your message to this supplier. Either you put the function in pos.
The module is provided with battery backup. Temperatures, times, operating conditions, parameter codes and alarm and fault codes Can be read from the display. Push the upper button until a parameter is shown 2.
OFF or you set an inter val. OFF-time Safety function in connection with sensor errors If the room sensor becomes defective is shor tcircuited or cut outthe controller will star t a regulating ranfoss of the compressor at the same time as an alarm is sounded for the sensor error. In controllers with a defrost relay you can set whether the defrost is to be made dznfoss electricity or hotgas.
Here you set for how long the exact measuring is to be suppressed. Normal operation or alarm Room temp. Emc display shows the actual room temperature, but by activating the keys the display changes To the set or the actual temperature of the defrost sensor.
EKC and are used for Temperature control Compressor control Fan motor control Defrost control Alarm signalling Danfoes only two keys, all functions can be set and programmed. Push the two buttons simultaneously See the temperatur at the defrost sensor 1. In the event of error function, the actual parameter code can be displayed. Here you can set the value at which the fan may star t. The controller comes prepared with plug and terminals, so all you have to do is to push the module into place.
This function is used when too long sensor cables have to be corrected.
Danfoss Temperature Controller Electronic Controller Ekc 201
Buttons If you want to change a setting, the two buttons will give you a higher or lower value depending on which button you push. The number of relays will then be increased by one.
Normal operation Room temp. When the thermostat calls for refrigeration, the compressor relay will be 021 in. Find the parameter code you want to change and then push the two buttons simultaneously.
Fan function Fan In addition to the fan functions concerning defrost the fans may also be stopped as a function of the compressor operation and a possible door function. Temperatures, times, operating conditions, parameter codes and alarm and fault codes Can be read from the display.
They signify the following: The controller has been specially designed for refrigeration applications, but may of course also be used for other forms of regulation where this is expedient. Service is provided by Bossgoo.
The temperature value is set. EKC and are used for Temperature control Compressor control Fan motor control Defrost control Alarm signalling With only two keys, all functions can be set and programmed. Installation guide for extended operation RC. Here you can set the time delay.
E Contains the general informations from this manual. Here is a list of the messages that can appear: If you push the top button in this situation, you will be able to see the alarm message in the display. Features One electronic controller is able to replace several traditional e,c and defrost clocks. Natural defrost on compressor stop. This means that the gateway with address in the system will have its alarm relay output activated for two minutes.
This input will register the position of a connected switch and depending on the functions you want to use, it will work, as follows: High-temperature alarm A1 High temp.
A01 Upper deviation Lower deviation Here you set when the alarm at low temperature is to become activated.