Life

FUTABA 12Z MANUAL PDF

June 18, 2019

Instruction manual • Read online or download PDF • Futaba 12Z User Manual. Futaba 12Z User Manual • Motor • Futaba Accessories communication. Read online or download PDF • Page / • Futaba 12Z User Manual • Futaba Accessories communication.

Author: Samuzuru Kazracage
Country: Reunion
Language: English (Spanish)
Genre: Business
Published (Last): 23 September 2007
Pages: 19
PDF File Size: 3.76 Mb
ePub File Size: 18.80 Mb
ISBN: 456-3-97572-591-4
Downloads: 78667
Price: Free* [*Free Regsitration Required]
Uploader: Nikogrel

For a description of the curve setting method, see the description at the back of this manual. Mxnual PCM mode, you can set eight linear channels and one digital channel. The T12Z is designed so that the airplane Before setting the model data, use the Model and glider including EP glider model types are Type function of the Linkage Menu to select the Page 21 Safety precautions when you install receiver and servos Warning Wood screw 2.

This function is designed to allow you to reset selected portions or all of the settings saved in Resets all the functions in the Model Menu the active model memory. This function is dedicated mixing used in needle adjustment of an engine that uses a fuel mixture control carburetor. Page 89 Setting method turn fytaba data input dial to the left and push the enter The rate and curve of each servo can be set by calling each screen.

Page Operation modes Symmetrical box mode The operation modes when stick, trim lever, or but left and right up and down operation is knob was selected are described below. It is used Fine tuning to correct undesirable tendencies when rudder is applied in roll maneuvers, knife edge, etc.

When raising the nose at a Adjustment majual independent curve for aileron, elevator, and pitch operations is possible. Up to 3 rates can be set for each condition.

This manual also for: For a description of the setting method, see the description at the back of this manual. Lever Head Lever Head 1. This function registers the T12Z user name. To add new models or to call a model already set, use the Model Select function of the Linkage Menu.

TOP Related Articles  CREATIVE JUNKIES YORIS SEBASTIAN PDF

Model addition and call Initial setting assigns 1 model to the T12Z transmitter. Manuual retail sales of Futaba, please visit your local dealer or Tower Hobbies. To print the manual completely, please, download it. Page Curve setting operation This section describes the setting procedure of curves which are used with the AFR function and each Curve type selection Curve type selection 1. Complain wrong Brand wrong Model non readable.

Futaba 12Z User Manual

After the set mode is changed from group mode [GROUP] to single mode [SINGL] at the control selection ,anual, only that condition setting is changed by control change; setting of other conditions remains the same.

Page 57 SUB-TRIM The Sub-Trim function is used to set the servo neutral position, and may be used to make fine adjustments to the control surface after linkages and pushrods are hooked up.

In order for you to make the best use of your system and to fly safely, please read this manual carefully. Updating following procedure to update the program.

Download Instructions Manuals: Futaba 12Z Radio control

Page 72 which can be switched by switch, etc. Mixing rate setting procedure The HR-3 is taken as an example to describe mixing rate setting. TIMER Each timer may be set for count-down or count The Timer function may be set for any desired time, up operation with a target time.

Two independent timers are provided futtaba your use. We recommend rutaba your system to the Futaba Service Center annually during your non-flying season for a complete checkup and service.

Function, Functions of linkage menu, Function change – Futaba 12Z User Manual

Table of Contents Add to my manuals Manuap. Adjustment of the fufaba lever length Adjustment of Throttle Stick Ratchet System You can also choose either airplane ratchet system or helicopter-touch. Page 75 For a description of the setting method, see the description at the back of this manual.

TOP Related Articles  2N5484 JFET DATASHEET PDF

When fugaba the receiver and servos to the fuselage, connect the necessary points in accordance with the kit instruction manual. It adjusts the a perpendicular position at neutral, the linkage swash-plate to operate correctly for each control compensation functions in this menu may not We immediately began to evaluate the backlog of Futaba parts and service requests, completing what mqnual be done with available parts.

BUTTERFLY This function allows powerful brake operation by simultaneously raising the left and right ailerons and lowering the flaps camber flap, position to be changed, the reference point is This setting will allow the ailerons to be raised while the flaps are simultaneously lowered.

If you have purchased this product from an exporter outside your own country and not the authorized Futaba dis- tributor in your country, please contact the seller immediately to determine if such export regulations have been met. Curve setting examples The screens shown below are curves created by the fuselage or the reference value.

Page Common operations used in function setup screen This section describes the functions often used at the function setup screen. As a result of this action we regret that we must return outstanding repairs and cancel any unfilled replacement parts requests. Trim mix function call can be linked to a stick, For a description of the setting ftaba, see Model type Select the model mahual f r o m a m o n g a i r p l a n ehelicopter, glider, and motor glider.

Page 6 Have regular maintenance performed. PIT to RUD mixing Revolution mixing Use this mix when you want to suppress the However, when a GY Series or other heading reaction torque generated by main rotor pitch and hold gyro is used, since correction is performed speed changes at pitch manuwl.